Troubleshooting guide for woven sack tape plant




PROBLEM
POSSIBLE CAUSES
SOLUTIONS
FILM PUNCTUREHold up particleChange screen pack. Check Row Material Moisture. Check heat stability of master batch.
GELES, HARD OR UNPLASTICIZED PROFILEImproper back pressure. Improper temp gradient. Moister in master batch.Change temp. Profile. Use fine wire mesh. Reduce die lip opening. Reduce adaptor flow area. Change screw geometry. Pre-dry master batch.
DENIER VARIATIONExtruder surging. Film thickness variation across width. Spacer thickness variation. Improper drive Performance.Refer problem III in general extrusion processing. Reduce throughput rate. Increase die volume. Adjust die lip. Check uniformity of die temp. Check spacer thickness. Use carbon steel blade. Check drive performance. Check temperature of orientation unit across width. Check flow velocity of hot air across width.
TAPE BREAKAGEExcessive stretch ratio. Low orientation temp. Hold up particle in film. Very stiff film. Extruder surgingIncrease stretch ratio. Increase orientation temperature. Refer problem of film puncture and gels, hard or unplasticized particles. Increase distance between die opening and water levels in tank.
LOW TENACITY / HIGHER ELONGATIONLow stretch ratio. Too soft film. Low orientation tempIncrease stretch ratio. Increase distance between die opening and water level in quenching tank. Increase orientation temp.
TAPE FABILATIONTape too stiff Scratches on tape moving path.Use anti fabrillation MB. Polish tape moving path. Use wear resistance material items.
SHRINKAGE IN FABRIC / CURVED TAPEResidual stress in tape.Check annealing system. Increase annealing temp. Check cooling efficiency of roller.





Comments

  1. Ashish DasJune 19, 2019 at 8:54 PM

    8004228560

    ReplyDelete
  2. UnknownJuly 23, 2019 at 1:42 PM

    9753246400

    ReplyDelete
  3. UnknownOctober 20, 2019 at 7:27 PM

    bad winding of bobbin

    ReplyDelete
  4. UnknownNovember 12, 2019 at 4:19 PM

    Ravi Shekhar
    8873053801

    ReplyDelete
  5. Buddha UdyogAugust 26, 2020 at 3:38 PM

    Great Blog..... Buddha Udyog is well known Non Woven Bags Manufacturers in Delhi, India who tried to put their small effort in an eco friendly environment if you want to know what we offer and we offer please check below:-


    U Cut Bags Manufacturers in Delhi
    D Cut Bags Manufacturers in Delhi
    Non Woven Fabrics Manufacturers in Delhi, India
    W Cut Bags Manufacturers in Delhi
    Non-Woven Bags Manufacturers in Gujarat
    Non Woven Bags Manufacturers in Indore
    Non Woven Bags Manufacturers in Saharanpur
    Non Woven Bags Manufacturers in Faridabad
    Non Woven Bags Manufacturers in Punjab
    Non Woven Bags Manufacturers in Odisha

    Thank You

    ReplyDelete
  6. Chandan kumarAugust 29, 2020 at 1:42 PM

    Kuch wander man ke vi hai kaya

    ReplyDelete
  7. Non Woven Bags ManufacturersOctober 8, 2020 at 5:50 PM

    Non Woven Bags Manufacturers in Delhi
    U Cut Bags Manufacturers in Delhi
    D Cut Bags Manufacturers in Delhi
    Loop Handle Bags Manufacturers in Delhi
    Promotional Bags Manufacturers in Delhi

    ReplyDelete
  8. UnknownDecember 18, 2020 at 12:03 PM

    Polyster Yarn Importer/Exporter around the world with best quality textile

    material. Also the best version of polyester yarn in china cotton yarn in

    china     in the textile industry.

    ReplyDelete
  9. Rahil KumarMay 31, 2021 at 6:16 PM

    Very nice post and also know about Masterbatch for water tanks

    ReplyDelete

Post a Comment

Get Here All Formula

Buy from here and get formula free

Popular posts from this blog

Woven sacks Circular looms formulas

Image
Picks per minute = cam RPM x Number of shuttles Gear Ratio = Haul off gear ratio X no of teeth of Haul off  Sprocket  ÷ motor gear  Sprocket .  Weaving Ring I.D = 2 x fabric width(mm)/3.14 OR = 2 x fabric width(inch) x 25.4/ 3.14  Elongation = Increase in length x 100 / Initial sample length Number of warp = 2 x fabric width x Warp Mesh (Inches) = 2 x fabric width x Warp Mesh / 2.54 (centimeters) Fabric Production per minute = 1.524 x PPM / Weft mesh Fabric GSM = Warp mesh x Warp Denier + Weft mesh x Weft Denier/228.6 Bags Weight = 50.8 x fabric width x Cut length x Warp mesh x Warp Denier + Weft mesh x Weft Denier/ 90,00,000 = Fabric Dfl. x Cut length X GSM/ 5000 ( warp mesh and weft mesh in inches, fabric width and cut length in inches) » For PP Unlaminated Fabric For Example, If you want to Produce 60cm x 90cm single fold bottom stitch 90 gram bag. For Production you need Two Things 1. Cut Length and 2. Denier For Cut Length :  Your Bag Length is 90cm + 4c
Read more

Some useful calculation for Tape Plant extrusion process (Woven Sack/ Raffia)

Image
Spacer Size (mm) = (Stretching Ratio) ^1/2 x Width of Tape Stretching Ratio = ( Spacer Size/Tape Width )^2 Stretching Ratio = Stretching Godet Speed / holding Godet Speed Production Kg/hr = Denier x Final Line Speed x No of Tapes x 60 / (9000x1000) Production Kg/hr = Denier x Final Line Speed x No of Tapes/ 150000 Elongation % = Tape Final Length - Initial Length x 100 / Final Length Tape Thickness Stretched = denier / (9000 x Tape Width x Density) Unstarched Tape Thickness = (Stretch Ratio )^1/2 x stretched Tape Thickness Denier Setting Formula = Holding Speed x Actual Denier / Required Denier Denier to GSM Calculator Relaxation Speed = Stretching Speed - Annealing Speed x 100 / Stretching Speed Screw Speed Formula = Motor Speed x Motor Pulley  Diameter / ( Gear Ratio x Gera Box Pulley Diameter) Useful Width ( Flat Film) = Film Width - ( 2 x Spacer size) Main Motor RPM = (Gear Ratio X Screw RPM X Gear Box Pulley Dia) /( Motor Pulley Dia.) Learn More About Tape Pla
Read more

Woven Sack (Raffia) Tutorial - Tape Plant Formula and important calculations

Image
Thank You for Watching For any further enquiry comment if you like this video please like and share on YouTube Spacer Size (mm) = (Stretching Ratio) ^1/2 x Width of Tape Stretching Ratio = ( Spacer Size/Tape Width )^2 Stretching Ratio = Stretching Godet Speed / holding Godet Speed Production Kg/hr = Denier x Final Line Speed x No of Tapes x 60 / (9000x1000) Production Kg/hr = Denier x Final Line Speed x No of Tapes/ 150000 Elongation % = Tape Final Length - Initial Length x 100 / Final Length Tape Thickness Stretched = denier / (9000 x Tape Width x Density) Unstarched Tape Thickness = (Stretch Ratio )^1/2 x stretched Tape Thickness Denier Setting Formula = Holding Speed x Actual Denier / Required Denier Relaxation Speed = Stretching Speed - Annealing Speed x 100 / Stretching Speed Screw Speed Formula = Motor Speed x Motor Pulley  Diameter / ( Gear Ratio x Gera Box Pulley Diameter) Useful Width ( Flat Film) = Film Width - ( 2 x Spacer size) Main Motor RPM = (Gear R
Read more